WATCO ArmourGrip – epoxy anti-slip system with iron silicate grit
€234.64
Product information "WATCO ArmourGrip – epoxy anti-slip system with iron silicate grit"
WATCO ArmourGrip is intended for floors where ordinary anti-slip paints wear through quickly: loading areas with constant forklift traffic, ramps, turning areas and busy aisles. Instead of a paint with mixed-in grit, it builds a thick epoxy layer into which a very hard iron silicate aggregate is broadcast.
The base is a 2-pack epoxy with 100% solids that builds around 600 µm in one coat. It is then topped with black aggregate with a Mohs hardness of 7.5 (manufacturer data). The result is a black, mid-gloss finish that the manufacturer rates at 77.8 PTV dry and 72.6 PTV wet, and that wears far more slowly than conventional coatings. It can be applied from 5 °C, usually without primer, on concrete, wood and most metals.
Typical applications
- Loading bays, loading zones and ramps
- Vehicle turning areas and busy aisles
- Damp, oily or slippery surfaces indoors and outdoors
Features
- Iron silicate grit, Mohs hardness 7.5 (manufacturer data)
- PTV 77.8 dry / 72.6 wet (manufacturer data)
- One coat, can be applied from 5 °C
- Black mid-gloss finish
Technical data (manufacturer)
| Base | 2-pack epoxy, 100% solids, plus 25 kg iron silicate grit |
|---|---|
| Substrates | Concrete, wood, most metals |
| Pack | 4 l resin/hardener + 25 kg grit, approx. 10 m² |
| Recommended coats | 1 |
| Film thickness | 600 µm |
| Pot life | 20 min at 20 °C, 30 min at 10 °C |
| Heavy traffic | 72 h at 5 °C, 48 h at 10–20 °C, 16 h at 30 °C |
| Min. floor temperature | 5 °C |
| Use | Indoors and outdoors |
| Limitations | Not for aluminium, stainless steel, chequer plate, asphalt or damp surfaces; do not steam clean |
Because of its coarse texture, the manufacturer advises that ArmourGrip is less suited to clean-room areas.
The slip resistance rating is manufacturer data from a standardised test method. Whether the surface is sufficient for your specific work area depends on contamination, moisture and use, and should be assessed as part of your risk assessment.
Hazard information under CLP (according to the manufacturer's safety data sheet)
Component: Resin
Signal word: Warning
Hazard statements: H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H411 Toxic to aquatic life with long lasting effects.
Precautionary statements: P280 Wear protective gloves. Wear eye protection or face protection. P273 Avoid release to the environment. P391 Collect spillage. P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Supplemental information: EUH205 Contains epoxy constituents. May produce an allergic reaction.
Component: Curing agent
Signal word: Danger
Hazard statements: H302+H332 Harmful if swallowed or if inhaled. H314 Causes severe skin burns and eye damage. H317 May cause an allergic skin reaction. H410 Very toxic to aquatic life with long lasting effects.
Precautionary statements: P280 Wear protective gloves, protective clothing and eye protection or face protection. P271 Use only outdoors or in a well-ventilated area. P273 Avoid release to the environment. P391 Collect spillage. P301+P310, P330, P331 IF SWALLOWED: Immediately call a POISON CENTER or doctor. Rinse mouth. Do NOT induce vomiting. P303+P361+P353, P310 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water. Immediately call a POISON CENTER or doctor. P305+P351+P338, P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor. P405 Store locked up. P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Component: Aggregate
Not classified as hazardous.
Wording of the H, P and EUH statements as per CLP Regulation (EC) No 1272/2008, Annexes III and IV; pictograms derived from the classification. The manufacturer's label and current safety data sheet are authoritative.
Note: The components may be classified as hazardous. We will send you the current safety data sheets with classification, labelling and H and P phrases on request before you order. Supplied to trade and industrial users only.
Downloads
Technical Details
| Operating Conditions: | Abrasion-resistant, Durable, For high-frequency use, For indoor use, For outdoor areas, For production environments, For warehouse, Slip-resistant, Wet conditions and rain |
|---|---|
| Sectors/Industry: | Automotive & Suppliers, Building & Facility Management, Industry & Production, Logistics & Warehousing, Maintenance & Technical Services, Ports, Shipbuilding & Offshore |
Login
Stock & Custom Solutions
Standard range from stock plus made-to-order solutions to your specifications.
Personal Expert Consultation
Direct contact with our experts – we find the technical solution for your problem.
Brand Quality
Products from renowned manufacturers – certificates and declarations of conformity per product on request.
Delivery DE & Nordics
Reliable delivery to Germany, Denmark, Norway, Sweden and Finland – Austria and Switzerland on request.
Our Bestsellers
The best-selling products for professional users.
About Hansehandel
What we at HANSEHANDEL, our products and solutions stand for
Our
Mission
Our mission is to make industrial procurement for our partners in Germany and Northern Europe as efficient and reliable as possible. We deliver not just products, but engineering expertise and dependable, personal support.
Our
Vision
We aim to be the agile partner for MRO solutions for companies in Scandinavia and Germany – with technical know-how, deep market understanding and a clear focus on industrial safety.
Frequently Asked Questions
Contact Us
We look forward to your technical challenge.
