WATCO Concrex Carbon Fibre – carbon fibre reinforced epoxy repair mortar
€93.99
Product information "WATCO Concrex Carbon Fibre – carbon fibre reinforced epoxy repair mortar"
Concrex Carbon Fibre is WATCO's epoxy repair mortar for potholes, spalling and damaged edges in concrete floors that carry forklifts and heavy loads. According to the manufacturer, light traffic can return after about one hour and heavy traffic after 4–5 hours, so the area is not out of action for days.
The mortar is reinforced with carbon fibre and ceramic and has a high resin content. That lets you feather it out to nothing as well as fill to depths of 50 mm. It bonds to concrete, metal and masonry and cures to a granite-hard, impervious, non-dusting surface that is chemical resistant and slip resistant.
Typical applications
- Holes and breakouts in warehouse and factory floors
- Slab edges, joint arrises and step nosings
- Ramps and transitions indoors and outdoors
Features
- 2-pack epoxy reinforced with carbon fibre and ceramic
- Compressive strength 55.2 MN/m², tensile strength 15.4 MN/m² (typical manufacturer data)
- Can be feather-edged, no top coat needed
- Curing agent in separate bottles, so part packs can be mixed
Technical data (manufacturer)
| Base | 2-pack epoxy with sand, carbon fibre and ceramic |
|---|---|
| Substrates | Concrete, metal, brick, masonry |
| Coverage | approx. 1.2 m² per 10 kg, approx. 3 m² per 25 kg at 5 mm |
| Thickness | feather edge up to 50 mm |
| Back in use | light traffic after approx. 1 h, heavy traffic after 4–5 h (20 °C) |
| Pot life | approx. 30 minutes |
| Max. service temperature | 60 °C |
| Use | Indoors and outdoors |
| Primer | usually not needed; bonding primer recommended for thin layers on smooth surfaces and highly stressed edges |
Sold in the UK as Concrex Carbon Fibre. For very deep holes, use Concrex Deep Fill as a base layer; for cold rooms, the Cold Set version.
Versions
| Container | Manufacturer part no. |
|---|---|
| 5 kg | CXCF05 |
| 10 kg | CXCF10 |
| 25 kg | CXCF25 |
Hazard information under CLP (according to the manufacturer's safety data sheet)
Component: Resin/aggregate blend
Signal word: Warning
Hazard statements: H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H412 Harmful to aquatic life with long lasting effects.
Precautionary statements: P280 Wear protective gloves. Wear eye protection or face protection. P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Supplemental information: EUH205 Contains epoxy constituents. May produce an allergic reaction.
Component: Curing agent
Signal word: Danger
Hazard statements: H314 Causes severe skin burns and eye damage. H317 May cause an allergic skin reaction. H361 Suspected of damaging fertility or the unborn child. H372 Causes damage to organs through prolonged or repeated exposure. H411 Toxic to aquatic life with long lasting effects.
Precautionary statements: P201 Obtain special instructions before use. P280 Wear protective gloves, protective clothing and eye protection or face protection. P273 Avoid release to the environment. P260 Do not breathe vapour. P391 Collect spillage. P308+P313 IF exposed or concerned: Get medical advice/attention. P301+P310, P330, P331 IF SWALLOWED: Immediately call a POISON CENTER or doctor. Rinse mouth. Do NOT induce vomiting. P303+P361+P353, P310 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water. Immediately call a POISON CENTER or doctor. P305+P351+P338, P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor. P405 Store locked up. P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Wording of the H, P and EUH statements as per CLP Regulation (EC) No 1272/2008, Annexes III and IV; pictograms derived from the classification. The manufacturer's label and current safety data sheet are authoritative.
Note: The components may be classified as hazardous. We will send you the current safety data sheets with classification, labelling and H and P phrases on request before you order. Supplied to trade and industrial users only.
Downloads
Technical Details
| Operating Conditions: | Abrasion-resistant, Chemical resistant, Durable, For indoor use, For outdoor areas, For production environments, For warehouse, For workshops, Impact resistant, Slip-resistant |
|---|---|
| Sectors/Industry: | Automotive & Suppliers, Building & Facility Management, Construction & Renovation, Industry & Production, Logistics & Warehousing, Maintenance & Technical Services |
Login
Stock & Custom Solutions
Standard range from stock plus made-to-order solutions to your specifications.
Personal Expert Consultation
Direct contact with our experts – we find the technical solution for your problem.
Brand Quality
Products from renowned manufacturers – certificates and declarations of conformity per product on request.
Delivery DE & Nordics
Reliable delivery to Germany, Denmark, Norway, Sweden and Finland – Austria and Switzerland on request.
Our Bestsellers
The best-selling products for professional users.
About Hansehandel
What we at HANSEHANDEL, our products and solutions stand for
Our
Mission
Our mission is to make industrial procurement for our partners in Germany and Northern Europe as efficient and reliable as possible. We deliver not just products, but engineering expertise and dependable, personal support.
Our
Vision
We aim to be the agile partner for MRO solutions for companies in Scandinavia and Germany – with technical know-how, deep market understanding and a clear focus on industrial safety.
Frequently Asked Questions
Contact Us
We look forward to your technical challenge.
