WATCO Epoxyguard Premium Anti-Slip Cold Cure – slip-resistant epoxy floor coating for cold buildings
€357.83
Product information "WATCO Epoxyguard Premium Anti-Slip Cold Cure – slip-resistant epoxy floor coating for cold buildings"
Epoxyguard Premium Anti-Slip Cold Cure (sold in the UK as Epoxicote High Build Cold Cure Anti Slip) solves a common winter problem: the floor needs work, but the building is unheated and standard epoxies barely cure. According to the manufacturer, this grade of WATCO's high-build epoxy is designed for floor temperatures from 5 °C, so maintenance does not have to wait until spring.
The ceramic-reinforced 2-pack system with 100% solids goes on in one coat of about 220 µm, with the anti-slip aggregate already blended in. The textured, glossy finish is easy to clean and resists oil, solvents and cleaning chemicals. Suitable for concrete, wood, metal and sound existing coatings that are not flaking. Avoid standing water on the surface for the first 7 days.
Typical applications
- Unheated warehouses, production halls and vehicle sheds
- Workshops and garages in the cold season
- Slip-prone areas with oil or chemical contact
Features
- Can be applied from 5 °C floor temperature (manufacturer data)
- One coat, 220 µm, aggregate pre-blended
- Wet pendulum value (PTV) 66 to BS 7976-2 (manufacturer data)
- Full chemical resistance after 7 days (manufacturer data)
- Further RAL colours on request
Technical data (manufacturer)
| Base | 2-pack epoxy, ceramic-reinforced, 100% solids |
|---|---|
| Substrates | Concrete, wood, metal, well-bonded existing coatings |
| Coverage | approx. 18 m² per 4 l (one coat) |
| Film thickness | 220 µm |
| Cure time | 30 hours at 5 °C |
| Min. floor temperature | 5 °C |
| Storage before use | at least 8 hours at 15–25 °C, do not freeze |
| Use | Indoors |
| Shelf life | 12 months unopened |
In heated buildings the standard Epoxyguard Premium Anti-Slip is the right choice, and the Rapid version where downtime is short.
The slip resistance rating is manufacturer data from a standardised test method. Whether the surface is sufficient for your specific work area depends on contamination, moisture and use, and should be assessed as part of your risk assessment.
Versions
| Colour | Container | Manufacturer part no. |
|---|---|---|
| Light grey | 4 l | EHBCCASLGRY4 |
| Grey | 4 l | EHBCCASMGRY4 |
| Dark grey | 4 l | EHBCCASDGRY4 |
| Black | 4 l | EHBCCASBLK4 |
| Blue | 4 l | EHBCCASMBLU4 |
| Green | 4 l | EHBCCASMGRN4 |
| Tile red | 4 l | EHBCCASTRD4 |
| Safety yellow | 4 l | EHBCCASSYL4 |
Hazard information under CLP (according to the manufacturer's safety data sheet)
Component: Resin
Signal word: Warning
Hazard statements: H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H411 Toxic to aquatic life with long lasting effects.
Precautionary statements: P280 Wear protective gloves. Wear eye protection or face protection. P273 Avoid release to the environment. P391 Collect spillage. P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Supplemental information: EUH205 Contains epoxy constituents. May produce an allergic reaction. EUH211 Warning! Hazardous respirable droplets may be formed when sprayed. Do not breathe spray or mist.
Component: Curing agent
Signal word: Danger
Hazard statements: H314 Causes severe skin burns and eye damage. H317 May cause an allergic skin reaction. H411 Toxic to aquatic life with long lasting effects.
Precautionary statements: P280 Wear protective gloves, protective clothing and eye protection or face protection. P273 Avoid release to the environment. P391 Collect spillage. P301+P310, P330, P331 IF SWALLOWED: Immediately call a POISON CENTER or doctor. Rinse mouth. Do NOT induce vomiting. P303+P361+P353, P310 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water. Immediately call a POISON CENTER or doctor. P305+P351+P338, P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor. P405 Store locked up.
Wording of the H, P and EUH statements as per CLP Regulation (EC) No 1272/2008, Annexes III and IV; pictograms derived from the classification. The manufacturer's label and current safety data sheet are authoritative.
Note: The components may be classified as hazardous. We will send you the current safety data sheets with classification, labelling and H and P phrases on request before you order. Supplied to trade and industrial users only.
Downloads
Technical Details
| Operating Conditions: | Abrasion-resistant, Chemical resistant, Cold environment, For indoor use, For production environments, For warehouse, For workshops, Oil-resistant, Slip-resistant, Solvent resistant |
|---|---|
| Sectors/Industry: | Agriculture & Forestry, Automotive & Suppliers, Industry & Production, Logistics & Warehousing, Maintenance & Technical Services, Trades & Workshops |
Login
Stock & Custom Solutions
Standard range from stock plus made-to-order solutions to your specifications.
Personal Expert Consultation
Direct contact with our experts – we find the technical solution for your problem.
Brand Quality
Products from renowned manufacturers – certificates and declarations of conformity per product on request.
Delivery DE & Nordics
Reliable delivery to Germany, Denmark, Norway, Sweden and Finland – Austria and Switzerland on request.
Our Bestsellers
The best-selling products for professional users.
About Hansehandel
What we at HANSEHANDEL, our products and solutions stand for
Our
Mission
Our mission is to make industrial procurement for our partners in Germany and Northern Europe as efficient and reliable as possible. We deliver not just products, but engineering expertise and dependable, personal support.
Our
Vision
We aim to be the agile partner for MRO solutions for companies in Scandinavia and Germany – with technical know-how, deep market understanding and a clear focus on industrial safety.
Frequently Asked Questions
Contact Us
We look forward to your technical challenge.
