WATCO Epoxyguard Premium Schnelltrocknend – rapid-curing epoxy floor coating
€334.55
Product information "WATCO Epoxyguard Premium Schnelltrocknend – rapid-curing epoxy floor coating"
Epoxyguard Premium Schnelltrocknend (sold in the UK as Epoxicote High Build Rapid) is the fast-curing version of WATCO's high-build epoxy floor coating. It is meant for sites that cannot close halls, warehouses or workshops for long: at 20 °C the floor can take light traffic after about 8 hours according to the manufacturer, so coating overnight or during a shift break becomes realistic.
Like the standard version, the solvent-free 2-pack system with 100% solids builds around 220 µm in a single coat. The glossy finish is easy to clean and resists oil, solvents and cleaning chemicals. It can be applied to concrete, wood and metal, and over existing worn floor coatings as long as they are not flaking. Very smooth or previously coated surfaces should be abraded first.
Typical applications
- Production halls and warehouses with short shutdown windows
- Workshops, vehicle areas and garages
- Areas where oil or chemicals may be spilled
Features
- Light traffic after approx. 8 hours at 20 °C (manufacturer data)
- One coat, 220 µm
- High abrasion and chemical resistance
- Solvent-free, therefore low odour
- Further RAL colours on request
Technical data (manufacturer)
| Base | 2-pack epoxy, 100% solids (resin + hardener) |
|---|---|
| Substrates | Concrete, wood, metal, well-bonded existing coatings |
| Coverage | approx. 18 m² per 4 l (one coat) |
| Film thickness | 220 µm |
| Cure time | 8 hours at 20 °C, 16 hours at 10 °C |
| Min. floor temperature | 15 °C |
| Finish | fine, glossy |
| Use | Indoors |
| Primer | usually not required; epoxy primer on very porous substrates |
| Shelf life | 12 months unopened, keep frost-free |
Where time is not critical, standard Epoxyguard Premium is sufficient; for cold rooms there is the Kalttrocknend (cold cure) version.
Versions
| Colour | Container | Manufacturer part no. |
|---|---|---|
| Light grey | 4 l | EHBRLGRY4 |
| Grey | 4 l | EHBRMGRY4 |
| Dark grey | 4 l | EHBRDGRY4 |
| Black | 4 l | EHBRBLK4 |
| Blue | 4 l | EHBRMBLU4 |
| Green | 4 l | EHBRMGRN4 |
| Tile red | 4 l | EHBRTRD4 |
| Safety yellow | 4 l | EHBRSYL4 |
Hazard information under CLP (according to the manufacturer's safety data sheet)
Component: Resin
Signal word: Warning
Hazard statements: H315 Causes skin irritation. H317 May cause an allergic skin reaction. H319 Causes serious eye irritation. H411 Toxic to aquatic life with long lasting effects.
Precautionary statements: P280 Wear protective gloves. Wear eye protection or face protection. P273 Avoid release to the environment. P391 Collect spillage. P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Supplemental information: EUH205 Contains epoxy constituents. May produce an allergic reaction.
Component: Curing agent
Signal word: Danger
Hazard statements: H302 Harmful if swallowed. H314 Causes severe skin burns and eye damage. H317 May cause an allergic skin reaction. H373 May cause damage to organs through prolonged or repeated exposure. H411 Toxic to aquatic life with long lasting effects.
Precautionary statements: P280 Wear protective gloves, protective clothing and eye protection or face protection. P273 Avoid release to the environment. P260 Do not breathe vapour. P391 Collect spillage. P301+P310, P330, P331 IF SWALLOWED: Immediately call a POISON CENTER or doctor. Rinse mouth. Do NOT induce vomiting. P303+P361+P353, P310 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water. Immediately call a POISON CENTER or doctor. P305+P351+P338, P310 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor. P405 Store locked up. P501 Dispose of contents and container in accordance with all local, regional, national and international regulations.
Wording of the H, P and EUH statements as per CLP Regulation (EC) No 1272/2008, Annexes III and IV; pictograms derived from the classification. The manufacturer's label and current safety data sheet are authoritative.
Note: The components may be classified as hazardous. We will send you the current safety data sheets with classification, labelling and H and P phrases on request before you order. Supplied to trade and industrial users only.
Downloads
Technical Details
| Operating Conditions: | Abrasion-resistant, Chemical resistant, For indoor use, For production environments, For warehouse, For workshops, Oil-resistant, Solvent resistant |
|---|---|
| Sectors/Industry: | Automotive & Suppliers, Industry & Production, Logistics & Warehousing, Maintenance & Technical Services, Mechanical & Plant Engineering, Trades & Workshops |
Login
Stock & Custom Solutions
Standard range from stock plus made-to-order solutions to your specifications.
Personal Expert Consultation
Direct contact with our experts – we find the technical solution for your problem.
Brand Quality
Products from renowned manufacturers – certificates and declarations of conformity per product on request.
Delivery DE & Nordics
Reliable delivery to Germany, Denmark, Norway, Sweden and Finland – Austria and Switzerland on request.
Our Bestsellers
The best-selling products for professional users.
About Hansehandel
What we at HANSEHANDEL, our products and solutions stand for
Our
Mission
Our mission is to make industrial procurement for our partners in Germany and Northern Europe as efficient and reliable as possible. We deliver not just products, but engineering expertise and dependable, personal support.
Our
Vision
We aim to be the agile partner for MRO solutions for companies in Scandinavia and Germany – with technical know-how, deep market understanding and a clear focus on industrial safety.
Frequently Asked Questions
Contact Us
We look forward to your technical challenge.
